Manufacturing Technology 2025, 25(6):751-757 | DOI: 10.21062/mft.2025.084

Comparison and Verification of Stress Measurement Results Using the Barkhausen Effect during Three-Point Bending

Tomasz Domański ORCID...1, Wiesława Piekarska ORCID...2, Milan Saga ORCID...3, Zbigniew Saternus ORCID...1, Marcin Kubiak ORCID...1, Milan Vasko ORCID...3
1 Faculty of Mechanical Engineering, Czestochowa University of Technology, Dabrowskiego 69, 42-201 Czestochowa, Poland
2 Faculty of Architecture, Civil Engineering and Applied Arts, University of Technology, Rolna 43, 40-555 Katowice, Poland
3 Faculty of Mechanical Engineering, University of ®ilina. Univerzitná 8215/1, 010 26 ®ilina. Slovak Republic

Non-destructive stress measurement techniques are extremely important and are still being developed in engineering research and diagnostics of materials. They allow for a quick assessment of their condition without damaging the structure. Their development is crucial for the safety of structures and extending the life of materials. One of the new methods is the measurement of stress using the Barkhausen effect. The MagStress 5d device was used for the tests. In this work, stress measurements were performed using the MagStress 5D device during three-point bending of a steel flat bar. The results were verified using resistance strain gauges and numerical simulation was performed in the Abaqus program. The measurements indicate that the MagStress 5d device using the Barkhausen effect can serve as a complete alternative to traditional extensometers. The results provided by the introduced method showed very good agreement with the latter.

Keywords: Bending testing, Numerical modelling, Barkhausen effect, Stress - strain analysis, S355 steel

Received: August 9, 2025; Revised: December 18, 2025; Accepted: December 18, 2025; Prepublished online: December 22, 2025; Published: December 23, 2025  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Domański T, Piekarska W, Saga M, Saternus Z, Kubiak M, Vasko M. Comparison and Verification of Stress Measurement Results Using the Barkhausen Effect during Three-Point Bending. Manufacturing Technology. 2025;25(6):751-757. doi: 10.21062/mft.2025.084.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. PIOTROWSKI, L., AUGUSTYNIAK ,B., CHMIELEWSKI, M., TOMAS, I., J. Magn. Magn. Mater, 2009, Vol. 321 pp. 2331-2335. Go to original source...
    2. CHENGUANG, W., CHANGQUAN, C.S. (2022). A critical examination of three-point bending for determining Young's modulus. In: International Journal of Pharmaceutics, Vol. 629, pp. 122409. Go to original source...
    3. STUPAKOV,O., UCHIMOTO, T., TAKAGI, T., J. Phys. D: Appl. Phys., 2010, Vol. 43 195003 (7pp). Go to original source...
    4. MAJKO J., VA©KO M., HANDRIK M., SÁGA M., Manufacturing Technology 2023, 23(2):216-224. Go to original source...
    5. STANCEKOVA D., MRÁZIK J., «AVODOVÁ M., SAPIETOVÁ A., RUDAWSKA A., TURIAN F., Manufacturing Technology 2022, 22(1):71-79. Go to original source...
    6. GATELIER-ROTHEA, C., CHICOIS, J., FOUGERES, R., FLEISCHMANN, P., Original Research Article Acta Materialia, Volume 46, Issue 14, 1 September 1998, Pages 4873 4882. Go to original source...
    7. JILES, D.C., GARIKEPATI, P., PALMER, D.D., NDT & E International, Volume 29, Issue 5, October 1996, Page 343.
    8. LINDGREN, M., LEPISTO, T., Mater. Sci. Tech. 18 1969-76.
    9. YELBAY CAM, H.I., GUR, C.H., E Int. 43 29-33.
    10. CHMIELEWSKI, M., PIOTROWSKI, L., AUGUSTYNIAK, B., Meas. Sci. Technol. 28., 2017. Go to original source...
    11. PIEKARSKA W., KUBIAK M., SATERNUS Z., Arch. of Metall. and Mater. 4, 57, 2012. Go to original source...
    12. YE T., CHEN B., LI Z., GAO Z., LIU K., REN Z., Manufacturing Technology 2025, 25(4):549-558. Go to original source...
    13. KORIC, S., THOMAS, B. (2007). Thermo-mechanical model of solidification processes with ABAQUS. In: Proceedings of the Abaqus Users' Conference, Paris. France. 22-24 May.
    14. VOURNA, P., HERVOCHES, Ch., VRÁNA, M., KTENA, A., HRISTOFOROU, E., IEEE Trans. Magn. 51 6200104.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content