Manufacturing Technology Journal, 2026 (vol. 26), issue 4
Design and Analysis of High-Precision Hydraulic Press Frame for Aviation Based on Finite Element Method
Lu Dong, Yaoming Fu, Jie Pang, Rui Nie, Zehua Hua
Manufacturing Technology 2026, 26(4):396-407 | DOI: 10.21062/mft.2026.041 
As the core equipment for aerospace product compression molding, the strength, stiffness, and dynamic stability of aviation high-precision hydraulic presses’ four-column frame directly determine product molding accuracy and production safety. This paper optimizes the frame structure and conducts multi-condition finite element analysis via ANSYS. Static strength analysis identifies initial stress concentration; after improvement, the maximum stress in pre-tightening and working states decreases by 41.87% and 66.20% respectively. Modal analysis shows uniform deformation of the first ten modes and confirms columns as the weak link, whose inner slope...
Model solution for vibrations of mechanical systems – Part I
Frantisek Klimenda, Blanka Skocilasova, Josef Soukup, Tereza Jarosova
Manufacturing Technology 2026, 26(4):408-423 | DOI: 10.21062/mft.2026.043 
The article deals with the solution of vertical vibrations of mechanical systems (machines). The introduction briefly characterizes the boundary conditions of the proposed solution, while the analytical solution itself is based on Lagrange's equation of the second kind. Its solution for this case is briefly outlined. A simplified spatial model of a material system is proposed, which allows changing the distribution of masses and various kinematic excitations of the resulting system. Relationships for the vertical displacement of individual points of the proposed mechanical system are derived for various variants of kinematic excitation. In the next...
Experimental Evaluation of the Influence of Different Types of Lubricants on the Tribological Resistance of Quenched and Tempered 42CrMo4 Steel
Mariana Kuffová, Michal Krbata, Marcel Kohutiar, Pavol Mikuš, Alena Breznická, Jana Escherova
Manufacturing Technology 2026, 26(4):424-432 | DOI: 10.21062/mft.2026.044 
This study investigates the influence of selected commercially available lubricants on the tribological behaviour of quenched and tempered 42CrMo4 steel intended for highly loaded mechanical and firearm components. Ten oils available on the domestic market were selected according to their ability to reduce friction, protect metallic surfaces and avoid silicone or PTFE-based additives. Reciprocating Ball-on-flat tests were performed using a Bruker UMT TriboLab with a G40 steel ball under a normal load of 50 N, a stroke length of 10 mm, a sliding speed of 0.3 m/min and a test duration of 20 min. The worn surfaces were evaluated using a LEXT OLS5100 3D...
EELS and EDS Spectroscopy of FeSi/NiAl Composite
Alena Michalcová, Václav Kaloč, Kateřina Skotnicová, Pavel Novák
Manufacturing Technology 2026, 26(4):433-437 | DOI: 10.21062/mft.2026.048 
This article describes details of lamellar eutectic part of FeSi/NiAl (2:1) in-situ composite prepared by infuction melting and followed by directional solidification by the Bridgman method. The material was formed by FeSi dendrites, and interdendritic spaces were filled by FeSi-NiAl eutectic, which was proven by EBSD observations. The phase boundaries are clearly visible, but all elements are detected in all phases. The energy dispersive spectroscopy in transmission electron microscope has proven that most significant contamination is by iron in the NiAl phase, where it replaces mainly Ni. The content of iron it the FeSi phase is close to the stoichiometry,...
Experimental Verification of the Effect of Fuel Additives on the Wear of Common Rail Pumps
Pavol Mikuš, Alena Breznická, Lucia Kakošová, Jozef Jaroslav Fekiač, Marcel Kohutiar, Maroš Eckert, Michal Krbaťa
Manufacturing Technology 2026, 26(4):438-445 | DOI: 10.21062/mft.2026.040 
The article addresses the issue of failures of high-pressure fuel pumps in Common Rail systems and evaluates the influence of fuel additives on their wear. The first part discusses the operating principle of the Common Rail system, the design of high-pressure fuel pumps, and the most common failure modes occurring during their operation. The experimental section focuses on the disassembly and visual analysis of a damaged pump, as well as on the experimental verification of the effects of summer and winter fuel additives in various ratios with diesel fuel. Tribological properties were evaluated using laboratory measurements, supplemented by non-destructive...
The Effect of Accelerated Weathering on the Properties of Coatings on an Aluminum Substrate
Katarína Moricová, Jana Šulcová, Iveta Papučová, Róbert Janík, Aleksandra Ewa Nowicka
Manufacturing Technology 2026, 26(4):446-452 | DOI: 10.21062/mft.2026.042 
Oxide coatings ZnO and TiO2 are characterized by good chemical stability, non-toxicity, photocatalytic activity, and the potential to improve the corrosion resistance of underlying materials. The aim of this study is to prepare and evaluate these environmentally friendly coatings applied to an aluminium sub-strate, which is one of the most widely used technical metals. X-ray fluorescence spectrometry employed was used to determine the chemical composition. Surface properties were investigated by measuring the contact angle on samples before exposure to UV radiation and condensation, and after 98 and 196 hours of exposure in a UV chamber. The structure...
Analysis of the Influence of Laser Welding Parameters on the Quality of the Lap Joint
Zbigniew Saternus, Wiesława Piekarska, Tomasz Domański, Ján Vavro jr., Marcin Kubiak, Pavol Čerňava
Manufacturing Technology 2026, 26(4):453-460 | DOI: 10.21062/mft.2026.037 
The analysis presented focuses on the relationship between laser welding parameters and the strength properties of lap joints. The objective of the research was to design a numerical model for estimating the strength properties of lap joints welded by laser beam. As part of the work, experimental tests were carried out and then numerical simulations were performed. Experimental tests were performed for a lap joint welded using two different welding depths. A joint with full and partial penetration of materials was obtained. The material used for the lap joint is two flat bars with dimensions of 100x200x2 [mm] made of X5CrNi18-10 austenitic steel. Mechanical...
Evaluation of Formability of Laser Tailor Welded Blanks
Alexander Schrek, Alena Brusilová, Zuzana Gábrišová, Pavol Švec
Manufacturing Technology 2026, 26(4):461-472 | DOI: 10.21062/mft.2026.045 
The car body construction is made from workpieces on which specific demands are put. The high stiffness and strength, low weight, programmable deformability is achieved by using of tailored welded blanks (TWBs). The weld joint is most commonly realized by a laser weld with a narrow heat affected zone (HAZ). The formability of TWB is affected by the weld, stress-strain characteristics of materials and process conditions. For the analysis of TWBs, materials with the same thickness, but different orientation of the texture of the individual parts with respect to the position of the weld, were used. The effect of surface anisotropy of individual materials...
Thermal Stability and Heat Treatment of Biomedical Co–28Cr–6Mo Alloy for Knee Implant Applications
Hana Thürlová, Ilona Voňavková, Dalibor Vojtěch
Manufacturing Technology 2026, 26(4):473-479 | DOI: 10.21062/mft.2026.047 
This study investigates the effect of heat treatment on cast Co–28Cr–6Mo biomedical alloy used for the production of knee implants. The alloy is widely used due to its excellent corrosion resistance, wear resistance, and mechanical properties. However, these properties can be further optimized by appropriate heat treatment. The thermal stability of the alloy was evaluated through hardness meas-urements and microstructural characterization. The highest hardness was achieved after annealing at 800 °C, which was associated with an increased fraction of the ε-phase with HCP crystal structure. In contrast, solution annealing followed by...
Effect of 3D printing on Changes in Modulus of Elasticity E Measured by Ultrasound, Bending Test and EBSD
Jana Vesela, Petr Beneš, David Bricín
Manufacturing Technology 2026, 26(4):480-486 | DOI: 10.21062/mft.2026.039 
The use of metal additive manufacturing is becoming an essential tool in industrial production, offer-ing opportunities for rapid innovation and increased efficiency. It is widely applied in prototype fabri-cation and spare‑part manufacturing, where it simplifies production processes, reduces costs, and shortens lead times. This study focuses on evaluating the influence of 3D printing parameters on the elastic modulus E measured in individual printing axes, and its change after thermomechanical post‑processing using Hot Isostatic Pressing (HIP). Elastic moduli were determined non‑destructively using ultrasonic testing and destructively...
Effect of Liquid Nitrogen Cooling on Machinability and Tool Wear Mechanisms in Cutting CGI-400
Shanshan Xu, Xu Sun, Fanning Meng, Yingqi Shen, Chunjing Shi, Ying Yang
Manufacturing Technology 2026, 26(4):487-496 | DOI: 10.21062/mft.2026.046 
This study systematically investigates the performance of liquid nitrogen cooling in machining compacted graphite iron 400 (CGI-400), compared with conventional cutting fluid cooling, focusing on mechanical properties, cutting temperature, tool wear, and surface quality. Results indicate that liquid nitrogen cooling significantly reduces the cutting temperature by 22.38%, effectively suppresses flank wear and built-up edge formation, and demonstrates remarkable advantages at cutting lengths beyond 3000 m. Cryogenic embrittlement of CGI-400 under liquid nitrogen leads to an 11.32% reduction in tensile strength, while the temperature-dependent thermal...
Enhancement of Hot Deep Drawing Die Wear Rate using Artificial Intelligence Lubricant Additive
Zaman Khalil Ibrahim, Jafar Keighobadi
Manufacturing Technology 2026, 26(4):497-516 | DOI: 10.21062/mft.2026.038 
Currently, lubricant additives represent an effective approach for addressing the increasing industrial demand for enhanced tribological performance and extended service life of forming tools. Graphene-based nanocomposites have shown considerable potential in reducing wear and friction while improving lubricant viscosity and thermal stability. Therefore, this study investigates the tribological performance of graphene-enhanced lubricants containing concentrations of 0, 2, 4, 6, 8, and 10 mg/ml graphene combined with 2 wt.% TiO₂ nano-additives under deep drawing conditions. Experiments were conducted within a temperature range of 25–150...


