Manufacturing Technology 2025, 25(2):239-243 | DOI: 10.21062/mft.2025.018

Analysis the Load of the Gantry Crane during Travelling along the Crane Track Using Working Model 3D

Ján Vavro ORCID..., Ján Vavro jr. ORCID..., Ľuboš Marček ORCID..., Jana Kuricová ORCID..., Miloš Taraba ORCID..., Lukáš Klimek ORCID..., Pavol Čerňava ORCID...
Faculty of Industrial Technologies in Púchov, Alexander Dubček University of Trenčín, I. Krasku 491/30, 020 01 Púchov, Slovakia

The paper presents the analysis of the gantry crane loading when driving along the crane track, using a Working model 3D, for which the analysis of the gantry crane frame loading was performed. The gantry crane is designed to remove dirt in front of the turbine under the water surface. For the gantry crane which moves along a track, the directional and vertical unevennesses were determined by experiment and are given in graphic and numerical form in (mm), relating to A track and B track with a total track length of 450 (m). Based on the knowledge of the unevenness of the rail track, the four random functional dependencies defining the irregularities of the individual rails as input variables were used for the kinematic excitation of the individual wheels of the gantry crane. The stress analysis was performed for a travel speed of 30 (m.min-1) and a lift of 10 (t) under the given loading. The results of the stress analysis are presented in graphic form.

Keywords: Loading, Virtual model, Load, Stress analyse, 3D model
Grants and funding:

This work was supported by the Slovak Grant Agency – project KEGA 011TnUAD-4/2024

Received: July 8, 2024; Revised: March 3, 2025; Accepted: March 24, 2025; Prepublished online: May 5, 2025; Published: May 6, 2025  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Vavro J, Vavro J, Marček Ľ, Kuricová J, Taraba M, Klimek L, Čerňava P. Analysis the Load of the Gantry Crane during Travelling along the Crane Track Using Working Model 3D. Manufacturing Technology. 2025;25(2):239-243. doi: 10.21062/mft.2025.018.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BRÁT, V., (1976), Handbook of Kinematics with Examples, Prague, SNTL
    2. DIŽO, J., HARUŠINEC, J., BLATNICKÝ, M. (2018). Computation of modal properties of two types of freight wagon bogie frames using the finite element method. In: Manufacturing Technology, Vol. 18, No. 2, pp. 208-214. J. E. Purkyne University in Usti n. Labem. Czech Republic Go to original source...
    3. GERLICI, J., GORBUNOV, M., KRAVCHENKO, K., DOMIN, R., LACK, T. (2017) Slipping and Skidding Occurrence Probability Decreasing by Means of the Friction Controlling in the Wheel-Braking Pad and Wheel-Rail Contacts. In.: Manufacturing Technology. Vol. 17, No.2, pp. 179-186, ISSN 1213-2489 Go to original source...
    4. HAUSER, V., NOZHENKO, O. S., KRAVCHENKO, K. O., LOULOVÁ, M., GERLICI, J., LACK, T. (2017). Impact of Wheelset Steering and Wheel Profile Geometry to the Vehicle Behavior when Passing Curved Track. In.: Manufacturing Technology ISSN 1213-2489 vol. 17, pp 306-312 Go to original source...
    5. KLIMENDA, F., SOUKUP, J., SKOČILASOVÁ, B., SKOČILAS, J. (2020). Vertical Vibration of the Vehicle when Crossing over Transverse Speed Bumps. DOI: 10.21062/mft.2020.020 Manufacturing Tech-nology. Vol. 20, No. 1 ISSN 1213-2489 Go to original source...
    6. KLIMENDA, F., SVOBODA, M., RYCHLIKOVA, L., PETRENKO, A. (2015). Investigation of Vertical Vibration of a Vehicle Vodel Driving Through a Horizontal Curve. In.: Manufacturing Technology ISSN 1213-2489 vol. 15, pp 143-148 Go to original source...
    7. LOULOVÁ, M., SUCHÁNEK, A., HARUŠINEC, J. (2017). Evaluation of the Parameters Affecting Pas-senger Riding Comfort of a Rail Vehicle. In.: Manufacturing Technology. Vol. 17, No 2, pp. 224-231, UJEP in Usti nad Labem, ISSN 1213-2489. Go to original source...
    8. PAUL, B., (1979) Kinematics and Dynamics of Planar Machinery, New Jersey, Prentice-Hall.
    9. SAGA, M., VAVRO, J., KOPECKÝ, M., (2002), Počítačová analýza a syntéza mechanických sústav. ISBN 80-968605-4-2, Žilina, 267 s.
    10. SCHWEIGHARDT, A., VEHOVSZKY, B., FESZTY, D. (2020) Modal Analysis of the Tubular Space Frame of a Formula Student Race Car. In.: Manufacturing Technology. Vol. 20, No. 1, DOI: 10.21062/mft.2020.013, ISSN 1213-2489 Go to original source...
    11. SVOBODA, M., CHALUPA, M., ČERNOHLÁVEK, V., ŠVÁSTA, A., MELLER, A., SCHMID, V. (2023). Measuring the Quality of Driving Characteristics of a Passenger Car with Passive Shock Absorbers. In.: Manufacturing Technology. Vol. 23, No. 1 ISSN 1213-2489 e-ISSN 2787-9402, DOI: 10.21062/mft.2023.023 © 2023 Go to original source...
    12. TOMSOVSKY, L., LOPOT, F., JELEN, K. (2022). Kinematic Analysis of the Tram-pedestrian Collision - a Preliminary Case Study. In.: Manufacturing Technology Vol. 22, No. 1 ISSN 1213-2489, DOI: 10.21062/mft.2022.007 © 2022 Go to original source...
    13. VAVRO, J., KOPECKÝ, M., VAVRO, J., JR., (2007), Nové prostriedky a metódy riešenia sústav telies III. ISBN 978-80-8075- 256-9, Žilina, 150 s.
    14. VAVRO, J., (2020), Kinematic and Dynamic Analysis of Planar Mechanisms by Means of the SolidWorks Software, Tribun EU s. r. o., ISBN 978-80-263-1495-0, p. 156.
    15. VAVRO, J., VAVRO, J., JR., (2019), Aplikácia výpočtových a experimentálnych metód v gumárenskom priemysle, ASSA spol. s.r.o., Púchov, 120 s.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content