Manufacturing Technology 2019, 19(6):973-978 | DOI: 10.21062/ujep/405.2019/a/1213-2489/MT/19/6/973

Development of the New Generation of Clamping Jaws for Thermomechanical Simulator

Tomáš Kalina, Václav Marek
Regional Technological Institute, Faculty of Mechanical Engineering, University of West Bohemia, 306 14 Pilsen. Czech Republic

This paper presents a development and design of new multifunctional clamping jaws for thermomechanical simulator. In the article there is presented what the thermomechanical simulator is and what is it used for. The article also describes the requirements for the thermomechanical simulator jaws and how they were achieved. All important parts of which the thermomechanical simulator jaws are assembled and used are described in detail. Finally, thermal simulations of the jaws were performed under operating loads. This technical solution is protected as a utility model registered on The Industrial Property Office - Czech Republic.

Keywords: Clamping jaws, thermomechanical simulator, heat treatment, forged parts
Grants and funding:

Project LO1502 ‘Development of the Regional Technological Institute’ under the auspices of the National Sustainability Programme I of the Ministry of Education of the Czech Republic aimed at supporting research, experimental development and innovation.

Published: December 1, 2019  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Kalina T, Marek V. Development of the New Generation of Clamping Jaws for Thermomechanical Simulator. Manufacturing Technology. 2019;19(6):973-978. doi: 10.21062/ujep/405.2019/a/1213-2489/MT/19/6/973.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BUBLÍKOVÁ, D., MAŠEK, B., VOREL, I., JENÍČEK, Š. (2017). Stability of Retained Austenite in High-Strength Martensitic Steels with Low Ms Temperature. In: Manufacturing Technology, Vol. 17, No. 4, pp. 428-433. ISSN 1213-2489 Go to original source...
    2. PEKOVIĆ, M., VOREL I., KÁŇA, J., OPATOVÁ, K. (2017) Evolution of Microstructure and Mechanical Properties in Steels during Isothermal Holding in the Region of Bainitic Transformation Temperature in Dependence on Silicon Content. In: Manufacturing Technology, Vol. 17, No. 4, pp. 549-555. ISSN 1213-2489 Go to original source...
    3. CHVAL, Z., SEDLÁČEK, F., KEMKA, V. (2017) Usage of FEM simulations in design of piping systems. Manufacturing Technology. In: Manufacturing Technology, Vol. 17, No. 4, pp. 469-473. ISSN 1213-2489 Go to original source...
    4. JENICEK, S., VRATISLAV, K., KALINA, T., MASEK, B (2016). Use of waterjet in manufacturing test bars of high-strength steels, Annals of DAAAM and Proceedings of the 27th DAAAM International Symposium, pp.0219-0224, Published by DAAAM International, ISBN 978-3-902734-08-2, ISSN 1726-9679, Vienna, Austria Go to original source...
    5. KÁŇA, J., VOREL, I., RONEŠOVÁ, A. Simulator of Thermomechanical Treatment of Metals. In DAAAM 2015. Vienna: DAAAM International Vienna, 2016. s. 0513-0518. ISBN: 978-3-902734-07-5, ISSN: 1726-9679 Go to original source...
    6. RONEŠOVÁ, A., MAŠEK, B., Digital generator of phase shift modulation, US Patent 7 480 155, 2009, Available from: www.google.com.ar/patents/US7480155.
    7. MAREK, V. (2016) BASIC RESEARCH OF THERMAL TRANSFER SIMULATIONS, Annals of DAAAM and Proceedings of the International DAAAM Symposium, 2016, pp. 578-585. ISBN: 978-1-5108-3300-5, Mostar
    8. MAREK, V. (2017). Thermal simulations based on macro-models. 28th International DAAAM Symposium on Intelligent Manufacturing and Automation 2017, Zadar, ISBN 978-3-902734-11-2 Go to original source...
    9. RAZ, K., CHVAL, Z. (2016) Temperature monitoring during injection molding process, 11th International Conference of DAAAM Baltic Industrial Engineering; Tallinn; Estonia; Volume 2016-April, 2016, Pages 71-74, 20 April 2016 through 22 April 2016; Code 135813
    10. CHVAL, Z., RAZ, K. (2016) Effect of heat load on amechanical forging press. 27th DAAAM International Symposium on Intelligent Manufacturing and Automation, DAAAM 2016; Mostar; Bosnia and Herzegovina; Volume 27, Issue 1, 2016, Pages 344-348. 26 October 2016 through 29 October 2016; Code 125666
    11. CHVAL, Z. (2013) Effect of heat load on a forging press. 27th DAAAM International Symposium on Intelligent Manufacturing and Automation, DAAAM 2016; Mostar; Bosnia and Herzegovina; Volume 27, Issue 1, 2016, Pages 344-348, 26 October 2016 through 29 October 2016; Code 125666
    12. KALINA, T., HELLER, P., CHVAL, Z., SEDLÁČEK, F., KŘÍŽEK M., BARTOŇ L., Numerical Simulation and Experimental Testing of Two-axle Chassis of Low-floor Trams, Manufacturing Technology: journal for science, research and production. Vol. 18, No. 2. Ústí nad Labem: Univerzita J.E. Purkyně v Ústí nad Labem, 2018. ISSN 1213-2489.
    13. KALINA T. Upínací čelistí (Clamping jaws), UŽITNÝ VZOR (UTILITY MODEL), n.doc.:33197, n.app..:2019-36482, 2019, owner: University of West Bohemia, registered on The Industrial Property Office, Czech Republic, Online: https://isdv.upv.cz/doc/FullFiles/UtilityModels/FullDocuments/FDUM0033/uv033197.pdf

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content