Manufacturing Technology 2019, 19(4):604-608 | DOI: 10.21062/ujep/341.2019/a/1213-2489/MT/19/4/604

Noise and Vibration Analysis of Conveyor Belt

Frantisek Klimenda, Josef Soukup, Jan Sterba
Faculty of Mechanical Engineering, J. E. Purkyne University in Usti nad Labem. Pasteurova 3334/7, 400 01 Usti nad Labem. Czech Republic

The article deals with the measurement of conveyor belt noise and vibration. The conveyor belt was supported on six rollers fixed on three plates of stand, return and drive drum. These six rollers were produced in two sets (convectional tube and accurate tube). Rollers were driven by a rubber belt. The noise was measured and evaluated on both sides of the conveyor. Vibration of the conveyor was measured at four locations of the conveyor construction. All measurements were performed in an unloaded condition. In conclusion of the article is a summary and evaluation of all measurements. The vibration of the conveyor is comparable in both cases, however, the rollers from accuracy tube excite the construction less, and this results in a lower total noise. By comparing the acceleration to the dominant frequency, it is obvious that the noise and the vibration of the belt conveyor construction were reduced by using rollers from accuracy tube

Keywords: Vibration, Noise, Conveyor belt
Grants and funding:

Grant UJEP-SGS-2018-48-002-2.

Published: August 1, 2019  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Klimenda F, Soukup J, Sterba J. Noise and Vibration Analysis of Conveyor Belt. Manufacturing Technology. 2019;19(4):604-608. doi: 10.21062/ujep/341.2019/a/1213-2489/MT/19/4/604.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. APETAUR, M. (2007): Acoustics of production machinery units and production areas (Akustika výrobních strojních celků a výrobních proctor), UJEP Ústí nad Labem, ISBN 978-80-7044-933-2
    2. NOVÝ, R. (2000): Noise and vibration (Hluk a chvění), ČVUT Praha, ISBN 80-02246-3
    3. DIŽO, J. (2015): Evaluation of Ride Comfort for Passengers by Means of Computer Simulation, Manufacturing Technology, Vol 15, No 1, ISSN 1213-2489 Go to original source...
    4. GERLICI, J., LACK, T., HARUČINEC, J. (2013): The Test Stand Load Modulus Implementation for the Realistic Railway Operation in the Laboratory Conditions, Manufacturing Technology, Vol 13, No 4, ISSN 1213-2489 Go to original source...
    5. SVOBODA, M., KLIMENDA, F., KAMPO, J., SOUKUP, J. (2015): Rollers vibrafon of conveyor belt. In: 13th International Conference on Dynamical Systems - Control and Stability, Lodž, 2015, Politechnika Lodž", pp. 571-578, ISBN 978-83-7283-708-0
    6. BLATNICKÝ, M., DIŽO, J., BLATNICKÁ, M. (2017): Side Plate Strength Analysis of the Mechanism for Vehicle Axle Scale Calibration, Manufacturing Technology, Vol 17, No 2, ISSN 1213-2489 Go to original source...
    7. LOULOVÁ, M., SUCHÁNEK, A., HARUŠINEC, J. (2017): Evaluation of the Parameters Affecting Passenger Riding Comfort of a Rail Vehicle, Manufacturing Technology, Vol 17, No 2, ISSN 1213-2489 Go to original source...
    8. KLIMENDA, F., SKOČILASOVÁ, B., (2017): Rollers Vibration of Pipe Conveyor, Manufacturing Technology, Vol 15, No 6, ISSN 1213-2489 Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content