Manufacturing Technology 2019, 19(3):461-468 | DOI: 10.21062/ujep/313.2019/a/1213-2489/MT/19/3/461

The Impact of Changes in InFeed Rate on Surface Integrity after Chrome Plate Grinding by Microcrystalline Corundum

Martin Marek, Martin Novák, Karel ©ramhauser
Faculty of Mechanical Engineering, J. E. Purkyně University in Usti nad Labem, Pasteurova 3334/7, 400 01 Ústí nad Labem

The efficient processing of materials, the development of machine concepts and grinding tools, as well as growing environmental and economic pressure are existing challenges in grinding. Chromium coatings are mainly used for components where corrosion protection is required, but also for the repair of worn parts. This paper presents and discusses the possibilities of utilizing changes in feed rate to achieve guaranteed surface integrity, which is very important for the life of the component. The results are presented in the form of tables and graphs, where I focus mainly on parameters of surface roughness and circularity.

Keywords: grinding, surface integrity, cutting conditions, hard chrome coating
Grants and funding:

Solar Turbines EAME Ltd.,
Project UJEP-SGS-2017-48-002-2.

Published: June 1, 2019  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Marek M, Novák M, ©ramhauser K. The Impact of Changes in InFeed Rate on Surface Integrity after Chrome Plate Grinding by Microcrystalline Corundum. Manufacturing Technology. 2019;19(3):461-468. doi: 10.21062/ujep/313.2019/a/1213-2489/MT/19/3/461.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. MÁDL, J., KAFKA, J., VRABEC, M., DVOŘÁK, R. (2000). Technologie obrábění. 3. díl. Praha: ČVUT. 2000. 81 s.
    2. G. E. DIETER. (1989). Mechanical Metallurgy. McGraw Hill Higher Education. 1989.
    3. L. JIANG. J. PARO. H. HÄNNINEN. V. KAUPPINEN AND R. ORASKARI. (1996). Comparison of grindability of HIP austenitic 316L. duplex 2205 and Super duplex 2507 and as-cast 304 stainless steels using alumina wheels. Journal of Materials Processing Technology. vol. 62. pp. 1-9. 1996. Go to original source...
    4. MAREK, M., NOVÁK, M. (2017). The Effect of Changes in Feed Rate on Surface Integrity during Nickel Coating Grinding, Solid State Phenomena, Vol. 261, pp. 207-214, 2017 Go to original source...
    5. NOVAK, M., NAPRSTKOVA, N. (2015). Grinding of the Alloy INCONEL 718 and Final Roughness of the Surface and Material Share. In: Manufacturing Technology, Vol. 15, No. 6 (2015) pp.1015-1023, ISSN: 1213-2489. Go to original source...
    6. MAREK, M., NOVÁK, M. (2016). Hodnocení drsnosti povrchu po brouąení niklového povlaku při změně řezných podmínek. Strojírenská Technologie. 2016. ročník XXI. číslo 1. s. 33-38. ISSN 1211 - 4162
    7. MARINESCU, Z., D., aj. (2007). Handbook of machining with grinding wheels. Boca Raton : CRC Press.2007. 592 s. ISBN 1-57444-671-1
    8. M.R KALANTARY. K.A HOLBROOK. P.B WELLS. (1993). Trans. Instut. Metal Finishing. 71 (2) (1993). p. 55 Go to original source...
    9. MAREK, M., NOVÁK, M., HOLESOVSKY, F., DURAKBASA, M., N. (2017). The Effect of Changes to Nickel Coating Machine on Surface Integrity and Microstructure after Grinding, In: Manufacturing Technology, Vol. 17, No. 6 (2017) pp.906-912, ISSN: 1213-2489. Go to original source...
    10. M. FIELD AND J. KAHLES. (1964). The surface integrity of machined and ground high strength steels. pp. 210: 54-77. 1964.
    11. MAREK, M., NOVÁK. M, (2017). The Effect of Changes in Feed Rate on Surface Integrity during Nickel Coating Grinding. Solid State Phenomena. Vol. 261. pp. 207-214. 2017 Go to original source...
    12. MADL, J. (2001). Theoretival aspect of precise machining. In I. International Congress of precision machining. Ústí nad labem. Czech Republic : ÚTŘV. J. E. Purkyne University. 2001. s 65-69. ISBN 80-7044-358-8
    13. MAREK, M., NOVÁK, M., RYTINA, T., DURAKBASA, M., N. (2017). Process and Equipment Improvement for Nickel Brush Plating Application. In: Manufacturing Technology. Vol. 17. No. 4 (2017) pp.503-507. ISSN: 1213-2489 Go to original source...
    14. Tvrdé chromování. BOMEX CZ. Bomex [online]. 1999 [cit. 2012-04-18]. Dostupné z: http://www.bomex.cz/cz/3-technologie/8-tvrde-chromovani.html
    15. JINFENG ZHANG, CHAO FENG, YUNHUI MA, WEI TANG, SHUAI WANG, XIN ZHONG. (2017). Nondestructive analysis of surface integrity in turning and grinding operations In: Manufacturing Technology, Vol. 17, No. 3, pp. 412-418, ISSN:1213-2489. Go to original source...
    16. MALLORY, G. O. a J. B. HAJDU. (1990). Electroplaters and Surface Finishers Society. Electroless plating: fundamentals and applications, Society, Orlando, Fla. 1990. 539pp. ISBN 978-0815512776

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content