Manufacturing Technology 2016, 16(1):45-48 | DOI: 10.21062/ujep/x.2016/a/1213-2489/MT/16/1/45

Evaluation of Cutting Forces and Surface Roughness after Machining of Selected Materials

Lenka Cepova1, Dagmar Sokova1, Sarka Malotova1, Bartosz Gapinski2, Robert Cep1
1 Faculty of Mechanical Engineering, VŠB - Technical University of Ostrava. 17. Listopadu 15/2172, Ostrava. Czech Republic
2 Faculty of Mechanical Engineering and Management, Poznan Univerzity of Technology, ul. Piotrowo 3, 60 965, Poznan. Poland

This article deals with the evaluation of changes in mean values of the individual components of cutting forces and measuring the roughness parameters after machining variable cutting conditions such as cutting speed and feed rate. Were evaluated 3 materials from different classes' machinability: steel 14109, alloy CuZn40Pb2 and brass AlCu4PbMg. The materials have been chosen with respect to their use in the extrusion method of the ECAP. The experiment was carried out on the machine SUI 40, the forces were measured on a dynamometer KISTLER 9441 and on the roughness equipment Hommel Tester T2000. All measurements will be evaluated in tables and graphs. The results could be used in abbreviated testing machinability as indicative.

Keywords: Machining; measuring; cutting forces; surface roughness

Published: February 1, 2016  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Cepova L, Sokova D, Malotova S, Gapinski B, Cep R. Evaluation of Cutting Forces and Surface Roughness after Machining of Selected Materials. Manufacturing Technology. 2016;16(1):45-48. doi: 10.21062/ujep/x.2016/a/1213-2489/MT/16/1/45.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. NESLUŠAN, M., TUREK, S., BRYCHTA, J., ČEP, R., TABAČEK, M. (2007). Experimentálne metódy v trieskovom obrábaní. Žilinská univerzita v Žilině/EDIS-vydavatelstvo ŽU, ISBN 978-80-8070-711-8.
    2. BUDA, J., BÉKÉS, J. (1977). Teoretické základy obrábania kovov. Alfa: Vydavatelstvo technickej a ekonomickej literatúry Bratislava, 696 s.
    3. BACH, P., POLÁČEK, M., CHVOJKA, P., DROBÍLEK, J. (2014). Dynamic Forces in Unstable Cutting during Turning Operation. Manufacturing Technology, Vol. 14, No. 1, pp. 3-8. ISSN 1213-2489. Go to original source...
    4. OČENÁŠOVÁ, L. (2004). Identifikácia obrábitelnosti materiálu ADI 1000 (Diplomová práca). Žilinská univerzita v Žilině.
    5. HRICOVÁ, J. (2013). Influence of Cutting Tool Material on the Surface Roughness of AlMgSi Aluminium Alloy. Manufacturing Technology, Vol. 13, No. 3, pp. 324-328. ISSN 1213-2489. Go to original source...
    6. HAVRILA, M., BRYCHTA, J. (2006). Top trendy v obrábání - Obrábané materiály. Media/st s.r.o.
    7. BRYCHTA, J., ČEP, R., NOVÁKOVÁ, J., PETŘKOVSKÁ, L. (2007). Technologie II - 1. díl. Ostrava: VŠB - TU Ostrava, ISBN 978-80-248-1641-8.
    8. Ferona-Materiálové normy [online]. [cit.2009-04-23]. Dostupný na: http://www.ferona.cz/cze/katalog/mat_normy.php
    9. Pramet-Katalog [online]. [cit.2009-04-27]. Dostupný na: http://www.pramet.com/download/katalog/pdf/Turning%202009%20CZSK%20screen.pdf
    10. CEP, R., JANASEK, A., PETRU, J., CEPOVA, L., CZAN, A., VALICEK, J. (2013). Hard Machinable Machining of Cobalt-based Superalloy. Manufacturing Technology, Vol. 13, No. 2, pp. 142-147. ISSN 1213-2489. Go to original source...

    Return to the content