Manufacturing Technology 2014, 14(3):407-412 | DOI: 10.21062/ujep/x.2014/a/1213-2489/MT/14/3/407

Setting of Angle of Soil Flow on Ploughshare at Traditional Processing of Soil

Stanislav Petrásek, Miroslav Müller
Faculty of Engineering, Czech University of Life Sciences Prague. Czech Republic

The soil is a considerable abrasive medium which exerts on tools processing the soil in a negative way. The main problem connected with using the soil processing machines is their wear owing to particles embedded in the soil. The ploughshare is one of the most loaded parts of the ploughing body and huge requirements are put on it. The aim of the research is to set an angle of a soil flow and connected wear of the ploughshare at the traditional processing of the soil. It is possible to further issue from ascertained pieces of knowledge at a production/renovation of the ploughshares with new functional surface. The statistical analysis evidenced that the angle of the soil flow on the ploughshare surface was the same with the angle of the ploughshare head. It followed from the measurements that the optimum angle for depositing the oblique overlay which is necessary for the creation of the serrated edge is in the interval 35 ± 4°.

Keywords: Composite, Functional surface, Optical analysis, Steel, Wear

Published: October 1, 2014  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Petrásek S, Müller M. Setting of Angle of Soil Flow on Ploughshare at Traditional Processing of Soil. Manufacturing Technology. 2014;14(3):407-412. doi: 10.21062/ujep/x.2014/a/1213-2489/MT/14/3/407.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. MÜLLER, M., CHOTĚBORSKÝ, R., VALÁ©EK, P., HLOCH, S. (2013). Unusual Possibility of Wear Resistance Increase Research in the Sphere of Soil Cultivation. In: Tehnicki Vjesnik-Technical Gazette, Vol. 20, No 4, pp. 641-646.
    2. MÜLLER, M., NOVÁK, P., HRABĚ, P. (2012). Innovation of material - constructional solutions of ploughing blade in area of conventional processing of soil during cultivating sugar beet. In: Listy cukrovarnické a řepařské, Vol. 130, No 3. pp. 94-99.
    3. MÜLLER, M., HRABĚ, P. (2013). Overlay materials used for increasing lifetime of machine parts working under conditions of intensive abrasion. In: Research in Agricultural Engineering, Vol. 59, No 1. pp. 16-22. Go to original source...
    4. DOUBEK, P., FILÍPEK, J. (2011). Abrasive and erosive wear of technical materials. In: Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 59(3), pp. 13-21. Go to original source...
    5. HORVAT, Z., FILIPOVI, D., KOSTIC, S., EMERT, R. (2008). Reduction of mouldboard plough share wear by a combination technique of hardfacing. In: Tribology International, Vol. 4. pp. 778-782.
    6. KEJVAL, J., MÜLLER, M. (2013). Mechanical properties of multi-component polymeric composite with particles of Al2O3/SiC. In: Scientia Agriculturae Bohemica, Vol. 44, No 4, pp. 237-242. Go to original source...
    7. MÜLLER, M., VALÁ©EK, P. (2012). Abrasive wear effect on Polyethylene, Polyamide 6 and polymeric particle composites. In: Manufacturing Technology, Vol. 12, No. 12, pp. 55-59. Go to original source...
    8. VOTAVA, J. et al. (2007). Abrasive wear of ploughshare blades made of Austempered Ductile Iron. In: Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, Vol. 55, No. 1, pp173-182. Go to original source...
    9. NATSIS, A., PAPADAKIS, G., PITSILIS J., (1999). The influence of soil type, soil water and share sharpness of a mouldboard plough on energy consumption, rate of work and tillage quality. In: Journal of Agricultural Engineering Research, Vol. 72, No. 2, pp. 171-176. Go to original source...
    10. NATSIS, A., PETROPOULOS, G., PANDAZARAS, C. (2008). Influence of local soil conditions on mouldboard ploughshare abrasive wear. In: Tribology International, Vol. 41, No. 3. pp. 151-157. Go to original source...
    11. CHOTĚBORSKÝ, R., HRABĚ, P., MÜLLER, M., SAVKOVÁ, J., JIRKA, M. (2008). Abrasive wear of high chromium Fe-Cr-C hardfacing alloys. In: Research of Agriculture Engineering, Vol. 54, No. 4. pp. 192-198. Go to original source...
    12. MÜLLER, M., VALÁ©EK, P., NOVÁK, P., HRABĚ, P., PA©KO, J. (2011). Overlays and composites application in technology of sugar beet cultivation and harvest. In: Listy cukrovarnické a řepařské, Vol. 127, No 9. pp. 304-307.
    13. HRABĚ, P., MÜLLER, M. (2013). Research of overlays influence on ploughshare lifetime. In: Research in Agricultural Engineering, Vol. 59, No. 4. pp. 147-152. Go to original source...
    14. KIM, I. S., SON, K. J., YANG, Y. S., YARAGADA, P. K. D. V. (2013). Sensitivity analysis for process parameters in GMA welding processes using a factorial design method. In: International Journal of Machina Tools and Manufacture, Vol. 43, pp. 763-769. Go to original source...
    15. MÜLLER, M., VALÁ©EK, P. (2012). Polymeric particle composites with filler saturated matrix. In: Manufacturing Technology, Vol. 12, No 13. pp. 272-276. Go to original source...
    16. MÜLLER, M., VALÁ©EK, P. (2012). Abrasive wear effect on Polyethylene, Polyamide 6 and polymeric particle composites. In: Manufacturing Technology, Vol. 12, No 12. pp. 55-59. Go to original source...
    17. SATAPATHY, B.K., BIJWE, J. (2002). Analysis of simultaneous influence of operating variables on abrasive wear of phenolic composites. In: Wear, Vol. 253, pp. 787-794. Go to original source...

    Return to the content